Dedicated CC-Link/LT Power Supply

Brand :

MITSUBISHI

Caution

Product Description

Power supply designed to supply power exclusively to CC-Link/LT systems from an external power source.
[Features]
· Power supply for general-purpose sequencer.
· Built-in 2‑A power supply.
· Stable 24 V DC.
[Applications]
· Power supply.
· Exclusively for CC-Link/LT.

Dedicated CC-Link/LT Power Supply Specifications

Dedicated CC-Link/LT Power Supply: related image

CL1PSU-2A external appearance

CL1PSU-2A dimensional drawing, unit: mm

Input	Rated Voltage	100/120/200/230/240 V AC
	Allowable Voltage Range	85 to 264 V AC
	Rated Current	1.2 A / 100 V AC, 0.7 A / 200 V AC
	Rated Frequency	50/60 Hz
	Power Supply Fuse	3.15 A
	Inrush Current	Max. 50 A / 100 V AC, Max. 60 A / 200 V AC
Output	Output Voltage	24 V DC +10%/-5%
	Output Current	0.01 to 2 A, Subject to derating depending on the ambient temperature and power supply voltage. [Use the system so that the total current consumption of each station does not exceed 2 A when power is supplied (except immediately after the power is turned on).]
	Ripple Noise	500 mVp‑p or less
Allowable Momentary Power Outage Duration		PS2: Operation continues after a momentary power outage of 10 ms or less.
Protection Grade		IP1X
Protection Function	Excess Current Protection	110 to 160%, drooping characteristics, automatically reset
Protection Function	Excess Voltage Protection	27 to 33 V, output cutoff, not automatically reset
External Connection Method		· Power supply to dedicated power supply: terminal block, 3 points (M3 screw) · Power supply to communication part and CC-Link/LT system: dedicated CC-Link/LT connector (4 pins) × 2
Mass		0.4 kg

Ambient Temperature			0 to 55°C - When Operating, -25 to 70°C - When Saving
Relative Humidity			5 to 95% RH (No Condensation) - When Operating / When Saving
Vibration Resistance	Under Intermittent Vibration	Frequency: 10 To 57 Hz	Single amplitude: 0.075 mm 10 times in each direction of X, Y and Z (total 80 minutes each)
	Under Intermittent Vibration	Frequency: 57 To 150 Hz	Acceleration: 9.8 m/s² 10 times in each direction of X, Y and Z (total 80 minutes each)
	Under Continuous Vibration	Frequency: 10 To 57 Hz	Single amplitude: 0.035 mm 10 times in each direction of X, Y and Z (total 80 minutes each)
	Under Continuous Vibration	Frequency: 57 To 150 Hz	Acceleration: 4.9 m/s² 10 times in each direction of X, Y and Z (total 80 minutes each)
Impact Resistance			147 m/s², 3 times in each direction of X, Y and Z
Noise Resistance			Achieved through a noise simulator with a noise voltage of 1,000 Vp‑p, noise width of 1 μs and frequency of 25 to 60 Hz.
Withstand Voltage			AC type: 15,000 V AC for 1 min DC type: 5,000 V AC for 1 min
Insulation Resistance			Between all external terminals at once and the earth terminal: 10 MΩ at 500 V DC on an insulation resistance meter
Operating Atmosphere			There shall be no corrosion gas or flammable gas and not much conductive dust.
Altitude Of Use			2,000 m or lower Cannot be used in environments pressurized higher than the atmospheric pressure. Doing so may cause failures.
Installation Location			Inside the control panel
Overvoltage Category			II or lower Indicates the assumed wiring part to which the applicable equipment is connected between the public network and the mechanical system in plant. Category II applies to the equipment to which power is supplied from a fixed facility. The surge withstand voltage for equipment of up to 300 V in rating is 2,500 V.
Pollution Degree			2 or lower Index to indicate the degree of conductive material generation in the use environment. Pollution degree 2 indicates that only non-conductive contaminants will generate. However, temporary conduction may still occur in the environment due to accidental condensation.
Earthing			D-type earthing (earthing resistance: 100 Ω or less)