Brushless Motor, Driver Single Unit, BLE2 Series
Caution
- The product image is a representative image.
Product Description
[Brand]Oriental Motor
[Power Supply Voltage]
・ Single-phase 100 to 120 V
・ Three-phase 200 to 240 V
・ Single-phase 200 to 240 / Three-phase 200 to 240 V
The BLE2 Series has a lineup of motors with electromagnetic brakes, dust-proof and waterproof specifications, as well as various lineups. It can be used for a wider range of purposes.
[Features]
・ Speed control range 80 to 4,000 r/min
・ Speed fluctuation rate ±0.2% (At the time of digital setting)
・ Torque can be limited
・ Multi-speed operation Up to 16 speeds
・ Holds the output shaft when stopped (Up to 50% of rated torque)
・ Protection rating IP66 (Motor part only)
・ High rust prevention and corrosion resistance due to stainless steel shaft
・ Monitor / test function useful for starting up the device and avoiding troubles
・ Digital settings and operations on the driver itself
・ Close contact mounting is possible with a compact and low profile driver
・ Speed can be set with a personal computer or an external signal
・ Cable with selectable pull-out direction
・ Up to 20 m between motor and driver with direct connection
・ Lineup 30 W to 400 W
General Specifications
| Item | Motor | Driver | |
|---|---|---|---|
| Insulation Resistance | 100 MΩ or more when a 500 VDC megger is applied between the windings and the case after continuous operation under normal ambient temperature and humidity. | After continuous operation at normal ambient temperature and humidity, the value measured with a 500 VDC megger between the power supply terminal and the protective earth terminal, and between the power supply terminal and the I/O signal terminal is 100 MΩ min. | |
| Dielectric Strength | No abnormality is observed even with an application of 1.5 kVAC at 50 Hz between the coils and the case for 1 minute after continuous operation at normal ambient temperature and humidity. | After continuous operation at normal ambient temperature and humidity, no abnormality is observed even if 50 Hz, 1.5 kVAC is applied between the power supply terminal and the protective earth terminal, and 50 Hz, 1.5 kVAC is applied between the power supply terminal and the I/O signal terminal for 1 minute. | |
| Temperature Rise | After rated continuous operation at normal ambient temperature and humidity, the temperature rise of the case surface measured by the thermocouple method is max. 65°C. | After continuous operation at normal ambient temperature and humidity, the measurement value of the temperature rise of the heat sink is 50 °C max. using the thermocouple method. | |
| Operating Environment*1 | Ambient Temperature | 0~+40°C (Non-freezing) | |
| Ambient Humidity | 85% max. (Non-condensing) | ||
| Altitude | Up to 1000 m above sea level | ||
| Atmosphere | No corrosive gases or dust. Should not be exposed to oil. Cannot be used in a radioactive area, magnetic field, vacuum, or other special environments. | No corrosive gases or dust. Should not be exposed to water or oil. Cannot be used in a radioactive area, magnetic field, vacuum, or other special environments. | |
| Vibration | Must not be subjected to continuous vibration or excessive shock. Conforms to JIS C 60068-2-6, "Sine-wave vibration test method". Frequency Range: 10~55 Hz, Half Amplitude: 0.15 mm, Sweep Direction: 3 directions (X, Y, Z), Number of sweeps: 20. | ||
| Storage Conditions*2 | Ambient Temperature | −20~+70°C (Non-freezing) | −25~+70°C (Non-freezing) |
| Ambient Humidity | 85% max. (Non-condensing) | ||
| Altitude | Up to 3000 m above sea level | ||
| Atmosphere | No corrosive gases or dust. Should not be exposed to water or oil. Cannot be used in a radioactive area, magnetic field, vacuum, or other special environments. | ||
| Thermal Class | EN Standards: 120 (E) | – | |
| Degree of Protection | IP67*3 (Excluding connector for driver connection) IP69K*4 (Excluding the installation surface, cable and connector for driver connection) | IP20 | |
*1 Install the driver to a location that has the same heat radiation capability as an aluminum metal plate.
Single Mounting 200×200mm, 2mm thickness
*2 The value for storage condition applies to short periods such as the period during transport.
*3 The IP indication that shows the watertight and dust-resistant performance are specified under IEC 60529 and IEC 60034-5.
*4 IP6X are specified under IEC 60034-5.IP9K are specified under DIN 40050-9.
Note:
• Do not measure insulation resistance or perform a dielectric strength test while the motor and driver are connected.
