Miniature Linear Guides - Standard Blocks with Dowel Holes, Light Preload / Slight Clearance

Brand :

MISUMI

Caution

We will stop the sale of Carbon Steel Miniature Linear Guide in 2021.
End of Sale Notification for MISUMI Carbon Steel Miniature Linear Guide Products
Delivery times for some of our products may be delayed as national government authorities have imposed limit of capacity at our production sites.

Product Description

Miniature Linear Guides - Standard Blocks with Dowel Holes, Light Preload / Slight Clearance
These linear guides or linear slides are factory automation components. They offer a wide variety of sizes to choose from.
[Feature]
● Rail Length Minimum/Maximum (mm.): 35 and 630
● Assembly Height (mm.): 8, 10, 13 and 16
● Accuracy Standards: Standard Grade and High Grade
● Block Type: Standard Block with Dowel Holes
● Material: Carbon Steel 56 HRC
[Application]
It is used in a variety of machines such as CNC machines, 3D printers, measuring instruments, and so on.

Type (Part Number)

Drawing

Specification / Dimensions Table

Basic Load Rating, etc.

Alterations (Optional)

Type (Part Number)

Material (Hardness)	Rail Length Type 1	Number of Blocks 2	Preload/AccuracyA			Lubrication Unit (MX) Equipped / Not EquippedB	Height (H) C	GreaseD 3
			Light Preload		Slight Clearance
			Precision Grade	High Grade	Standard Grade
No Surface Treatment Stainless Steel [SUS440C Equivalent] (56HRC or more)	Standard length (Selectable)	1	SSEBNV	SSEBN	SSEBNZ	Blank: None -MX: Provided	8 10 13 16 20	Blank: Standard G : Grease G L : Grease L Y: Grease Y H: Grease H
	Standard length (Selectable)	2	SSE2BNV	SSE2BN	SSE2BNZ
	1 mm increments (Dimension Configurable)	1	SSEBNLV	SSEBNL	SSEBNLZ
	1 mm increments (Dimension Configurable)	2	SSE2BNLV	SSE2BNL	SSE2BNLZ
Low Temperature Black Chrome Plating Stainless Steel [SUS440C Equivalent] (56HRC or more)	Standard length (Selectable)	1	-	RSEBN	-	None
	Standard length (Selectable)	2	-	RSE2BN	-
	1 mm increments (Dimension Configurable)	1	-	RSEBNL	-
	1 mm increments (Dimension Configurable)	2	-	RSE2BNL	-

1If the desired rail length is not available in the standard length (selectable), please specify the length in 1 mm increments (dimension configurable).

2If a 3- to 4-block product is desired, please select a part number for a 1-block product and specify "B3 (3 blocks)" or "B4 (4 blocks)" for alterations.

3*Only standard grease is available for the MX (with lubrication unit) type.

[ ! ] Heat resistance temperature is -20 to 80°C.

[ NG ] Blocks and rails cannot be purchased separately.

Part Number Configuration

Type	Height H	Grease	-	Rail Length L	-	Alterations
A B	C	D
SSEBN	10		-	275			（SSEBN10-275）
SSE2BNL-MX	10		-	271	-	MC	（SSE2BNL-MX10-271-MC）
SSEBNLV	10	G	-	271	-	MC-B4	（SSEBNLV10G-271-MC-B4）

Drawing

[ ! ] For L Dimension Configurable Type, G dimensions differ from those shown in the table below.
[ NG ] Blocks and rails cannot be purchased separately.

■ L Dimension　Unit：(mm)
Tolerance

L Dimension Range	Tolerance
25 ≤ L ≤ 400	0 -0.8
25 ≤ L ≤ 400	0 -0.8
400 < L ≤ 1000	0 -1.0
400 < L ≤ 1000	0 -1.0

■ H/W₂ Dimensional Accuracy

Type	Accuracy Standards	Assembly Height（H）	Precision（μm）
			Precision Grade	High Grade		Standard Grade
				No Surface Treatment	Low Temperature Black Chrome Plating
				No Surface Treatment	Low Temperature Black Chrome Plating
Miniature Linear Guide	Height H Tolerance	6 to 20	±10	±20	+30 -20	±20
	Pair Variation of Height H		7	15	15	40
	Width W₂ Tolerance		±15	±25	±25	±25
	Pair Variation of Width W₂		10	20	20	40

■ Tolerances of Other Symbols

Dimension Range		Tolerance （mm）
Over	or Less	Tolerance （mm）
0.5	3	±0.1
3	6	±0.1
6	30	±0.2
30	120	±0.3
120	400	±0.5
400	1000	±0.8
1000	2000	±1.2

Compliant with JIS B 0405-1991
Class m (intermediate)

[ ! ]The precision of low temperature black chrome plated Miniature Linear Guides is as shown above.
The sliding resistance is higher than that of Standard Type: approx. 1.2 N or lower.

Specification Table

Part Number				L 4	Block Dimensions								Dowel Hole Dimensions			Rail Dimensions
Type		MX	H		W	L₁	B	C	S × ℓ	L₂	K	Cb	N	C₂	(ℓ₁)	W₁	W₂	H₁	Ca	Counterbored Hole	F	G 5
Type		MX	H		W	L₁	B	C	S × ℓ	L₂	K	Cb	N	C₂	(ℓ₁)	W₁	W₂	H₁	Ca	d₁ × d₂ × h	F	G 5
1 Block SSEBN SSEBNL SSEBNV SSEBNLV SSEBNZ SSEBNLZ RSEBN RSEBNL	2 blocks SSE2BN SSE2BNL SSE2BNV SSE2BNLV SSE2BNZ SSE2BNLZ RSE2BN RSE2BNL	—	8	40 to 310 (70)	17	23.6	12	8	M2 × 2.5	13.6	6.5	0.3	8.5	8	2	7	5	4.7	0.3	2.4 × 4.2 × 2.3	15	5
		Blank: None -MX: Provided	10	35 to 635 (95)	20	30	15	10	M3 × 3	19	7.8	0.3	10	10	2.5	9	5.5	5.5	0.3	3.5 × 6 × 3.5	20	7.5
			13	45 to 970 (120)	27	33.9	20	15	M3 × 3.5	19.9	10	0.5	13.5	14	3	12	7.5	7.5	0.5	3.5 × 6 × 4.5	25	10
			16	70 to 990 (150)	32	42.4	25	20	M3 × 4	27.4	12	0.5	16	20	4	15	8.5	9.5	0.5	3.5 × 6 × 4.5	40	15
			20	100 to 1000 (160)	40	50	30	25	M4 × 6	34.6	15	0.5	20	25	4	20	10	11	0.5	6 × 9.5 × 5.5	60	20

4Dimensions in ( ) are for 2 Block Type.

4For 1 mm increments (Dimension Configurable), H20 will be up to 939 mm.

5For L Dimension Configurable Types, both ends of the rail are evenly cut. G dim. resulting from this cutting process will differ from those indicated on the above table.

[ ! ]H8 comes with cap bolts (M2 × 6).

[ ! ]Correctly match the datum planes (the side with the straight grooves) of both the rail and block.

[ NG ]Blocks and rails cannot be purchased separately.

Standard Rail Length (Selectable) List

The table below lists the standard rail lengths for each size. Please select the rail length from here.
Lengths not listed in the table below can be custom specified in 1 mm increments.

Height (H)	Rail Length (L)
8	(40)	(55)	70	85	100	115	130	145	160	175	190	205	220	235	250	265	280	295	310
10	(35)	(55)	(75)	95	115	135	155	175	195	215	235	255	275	295	315	335	355	375	395	415	435	455	475	495	515	535	555	575	595	615	635
13	(45)	(70)	(95)	120	145	170	195	220	245	270	295	320	345	370	395	420	445	470	495	520	545	570	595	620	645	670	695	720	745	770	795	820	845	870	895	920	945	970
16	(70)	(110)	150	190	230	270	310	350	390	430	470	510	550	590	630	670	710	750	790	830	870	910	950	990
20	(100)	160	220	280	340	400	460	520	580	640	700	760	820	880	940	1000

[ ! ] The dimensions in ( ) are not available for the standard 2-block type.

Basic Load Rating, Allowable Static Moment, Mass, Friction Resistance (Required Thrust), Sliding Resistance (Seal Resistance)

kgf = N × 0.101972

Height (H)	Basic Load Rating 6		Allowable Static Moment						Mass
	C (Dynamic) kN	Co (Static) kN	Block 1 pc.			Block 2 pcs. in close contact 7			Block kg	Guide Rail kg/m
	C (Dynamic) kN	Co (Static) kN	M_A N⋅m	M_B N⋅m	M_C N⋅m	M_A N⋅m	M_B N⋅m	M_C N⋅m	Block kg	Guide Rail kg/m
8	0.9	1.5	4.1	4.1	5.2	15.8	15.8	10.4	0.01	0.19
10	1.5	2.5	5.1	5.1	10.2	32.9	32.9	20.4	0.02	0.31
13	2.2	3.3	8.8	9.5	16.1	51.3	51.3	32.2	0.04	0.61
16	3.6	5.4	21.6	23.4	39.6	118.2	118.2	79.2	0.06	1.02
20	5.2	8.5	48.4	48.4	86.4	143.3	143.3	172.8	0.12	1.65

6The basic load rating is the same for all four directions (radial, reverse-radial, and lateral directions) relating to blocks. Can be used in any orientation.

7The allowable static moment when two blocks are in close contact is not a guaranteed value but a reference value.

The guideline for the allowable load and allowable moment of the linear guide is the value obtained by dividing each value (above table) by the static safety factor fs (below table).
Example: Allowable load (kN) for H10 under normal driving conditions: 2.5/2 = 1.25 (Approx. 128 kg)
The actual friction resistance (required thrust) when using a linear guide will vary depending on the load and other factors.

Static Safety Factor (Lower Limits of fs)

Condition of Use	Lower Limits of fs
For normal operating condition	1 to 2
When smooth running performance is required	2 to 4
When there is vibration or impact	3 to 5

Allowable Load (N) ≤ Co/fs
Allowable Moment (N⋅m) ≤ (M_A, M_B, M_C)/fs

fs: Static Safety Factor Co: Basic Static Load Rating
M_A, M_B, M_C: Allowable Static Moment (N⋅m)

Friction Resistance (Required Thrust Force)

・In linear guides, the rolling elements perform rolling motion, resulting in lower frictional resistance compared to sliding guides.
However, this can vary depending on the applied load, speed, and the characteristics of the lubricant.
Especially when a moment load is applied or preload is applied, friction resistance increases. Although seal resistance varies depending on the seal lip press-fit allowance
and the condition of the lubricant, it is not proportional to load and always shows a constant value. Friction resistance is obtained by the following formula.

F＝μ・w＋f

F: Friction Resistance (N)
μ: Dynamic Friction Coefficient
w: Load (N)
f: Sliding Resistance (Seal Resistance)

Dynamic Friction Coefficient

Type	Dynamic Friction Coefficient (μ)
Miniature Linear Guide	0.004 to 0.006
Linear Guides for Medium Load	0.002 to 0.003

Calculation Example

Condition: Miniature linear guide (standard rail) assembly height (H): 10: Sliding resistance (seal resistance): 0.5 (N)
Dynamic Friction Coefficient (μ): 0.005
Load: 150 (N)

F (Friction Resistance)＝0.005×150+0.5＝1.25(N)

Mounting and Handling

■ Datum Plane and Mounting Direction

Datum plane has the Datum Plane Mark (groove) on the block and rail (Fig. A). Be sure to match the datum planes for use.
The mounting direction shown in Fig. B is acceptable. All the basic load ratings are same.

Fig. A

Fig. B

■ Precautions for Use

[ ! ] Blocks are equipped with retainers (wires) to prevent the balls from derailing.
[ ! ] Radial clearances and accuracies are not guaranteed if the blocks and rails are interchanged from the original set combinations..
[ ! ] Straight grooves are provided on datum planes. Be sure to match the datum planes for use. Be sure to match the datum planes for use.
[ ! ] Rails cannot be connected end to end.
[ ! ] The accuracy of Linear Guides is guaranteed after mounting the rail (after fastening screws on the rail and pushing it onto the datum plane).
Minor bending of the rail will be adjusted by being secured and will not affect the performance.

■ Accessory

H8 comes with cap bolts (M2 × 6).

■ About Grease

Filled with a standard grease: lithium soap based grease (Multemp Grease PS2 by KYODO YUSHI) before shipment.
The standard grease when selecting the lubrication unit MX is (ENEOS Corporation Tufflix MP2).
Greasing with a different brand of grease is not recommended. Please use the same brand of grease.
Apply grease directly to the rail. After applying, move the block to let the grease absorb.

■ Grease fitting position when selecting lubrication unit MX

The miniature type does not come with a grease fitting or greasing hole.
When lubrication unit MX is selected: When the datum plane is in front, the grease fitting is attached in the direction shown in the diagram below.

■Lubrication Unit

Advantages of Lubrication Unit MX:
The oil-impregnated porous core part has been built into the product.
Provides long term maintenance-free operation.
Reduces maintenance cost.
Most suitable where the design does not allow lubrication.

Alterations

Code

Alterations

Specifications

Notes

Change rail counterbore holes to tapped holes

·Changes the guide rail mounting holes from counterbored holes to tapped holes.

! Not applicable for H dim. 8 ≥ 131, H dim. 10 ≥ 276, H dim. 13 ≥ 471, H dim. 16 ≥ 671, or H dim. 20 ≥ 701
! See the table below for the tapped hole dimensions after change.

Dimension H	Tapped Hole Dimensions
8	M 3
10	M 4
13	M 4

Dimension H	Tapped Hole Dimensions
16	M 5
20	M 6

LLC
RLC

LLC: Left End Cut
RLC: Right End Cut

·Cuts rail ends.
·Rails are cut with the engraved side as front (datum plane as back).
(as shown in the image on the left)
·Please refer to the table below for the length of the rail to be cut.

Dimension H	L Cut	N
10	2.5	5
13	5
16	10

!The overall length will be shortened by the amount of cutting.
Example: The L dimension of SSEBN13-95-LLC is 90 mm.
!Applicable only to Selectable Type (standard rail length).
!Not applicable to H8 and 20.
!Not applicable to L35 of H10 and L45 of H13.

B3
B4

B3: Additional Block (Total 3 pcs.)
B4: Additional Block (Total 4 pcs.)

3-Block Specifications

4-Block Specifications

·It will be shipped with 3 (4) blocks installed.
·There is a minimum length limit for the L dimension (rail length).
Please refer to the table below "Shortest Selectable Rail Lengths for B3/B4."

!Please specify the part number for one block.
(× SSE2BN10-215-B4)

■ Shortest Selectable Rail Lengths for B3/B4

H	B3 (3 blocks)	B4 (4 blocks)
8	85	115
10	115	155
13	145	170
16	190	230
20	220	280

App. Example

― Installation Examples ―
Conventional Type With Dowel Holes
Positioning on the basis of plate end face Positioning using a dowel hole

App. Example

- Installation Examples -
Conventional Type	With Dowel Holes

Positioning on the basis of plate end face	Positioning using a dowel hole